News
![DEANS® Tech Bench - Ultra Plug® vs. T-Plug Clones - Parallel Amp Test](http://www.wsdeans.com/cdn/shop/articles/20240307_102337.jpg?v=1709835932&width=533)
DEANS® Tech Bench - Ultra Plug® vs. T-Plug Clon...
Here at W.S. Deans, we are proud to offer high quality connectors. The most critical feature of a connectors is its ability to pass current by minimizing resistance. In the...
DEANS® Tech Bench - Ultra Plug® vs. T-Plug Clon...
Here at W.S. Deans, we are proud to offer high quality connectors. The most critical feature of a connectors is its ability to pass current by minimizing resistance. In the...
![Deans® Tech Bench](http://www.wsdeans.com/cdn/shop/articles/20240307_102337_5ae1ffc7-be1f-4edb-a6db-05756b2f4d5e.jpg?v=1712419669&width=533)
DEANS® Tech Bench - Can the Deans® Ultra Plug® ...
We get asked all the time, "How much can it handle?" Well it will always depend on how the system is built and how long the current is applied. That being...
DEANS® Tech Bench - Can the Deans® Ultra Plug® ...
We get asked all the time, "How much can it handle?" Well it will always depend on how the system is built and how long the current is applied. That being...
![DEANS® Tech Bench - Heat Matters](http://www.wsdeans.com/cdn/shop/articles/HotCarMotor_ESC.jpg?v=1712419432&width=533)
DEANS® Tech Bench - Heat matters in the system
Temperature can be both good and bad for the performance of your vehicle. In the news, we have heard about the drawbacks of the of electric vehicles (EVs) in cold...
DEANS® Tech Bench - Heat matters in the system
Temperature can be both good and bad for the performance of your vehicle. In the news, we have heard about the drawbacks of the of electric vehicles (EVs) in cold...
![DEANS® Engineering - Step 5 Can we make it more professional](http://www.wsdeans.com/cdn/shop/articles/20240212_121055.jpg?v=1708625799&width=533)
DEANS® Engineering - Step 5 Can we make it more...
Last time, we made a version that was lasercut rather than 3D printed. 3D printing is great for prototyping, but can take quite a while to make. Lasering or injection...
DEANS® Engineering - Step 5 Can we make it more...
Last time, we made a version that was lasercut rather than 3D printed. 3D printing is great for prototyping, but can take quite a while to make. Lasering or injection...
![DEANS® Engineering - Step 4 It feels too small](http://www.wsdeans.com/cdn/shop/articles/20240221_113630.jpg?v=1708625110&width=533)
DEANS® Engineering - Step 4 It feels too small
In the previous post, we 3D printed a small connector holder. It just did not feel robust enough. Yes, I said "feel". In product design there are elements of fit,...
DEANS® Engineering - Step 4 It feels too small
In the previous post, we 3D printed a small connector holder. It just did not feel robust enough. Yes, I said "feel". In product design there are elements of fit,...
![Deans Dealers: Visiting Ultimate Hobby in Orange, California](http://www.wsdeans.com/cdn/shop/articles/UltimateHobbyCA.png?v=1709234886&width=533)
Deans Dealers: Visiting Ultimate Hobby in Orang...
The dealers of make up an important part of the distribution of genuine Deans products. We like to thank those that have supported us and through the years. In this...
Deans Dealers: Visiting Ultimate Hobby in Orang...
The dealers of make up an important part of the distribution of genuine Deans products. We like to thank those that have supported us and through the years. In this...